ATS177
SINGLE OUTPUT HALL EFFECT LATCH
ATS177
Document number: DS31055 Rev. 6 - 2
1 of 9
www.diodes.com
July 2010
?Diodes Incorporated
Description
ATS177 is an integrated Hall-Effect latch sensor designed for
electronic commutation of brush-less DC motor applications.
The device includes an on-chip Hall voltage generator for
magnetic sensing, a comparator that amplifies the Hall
voltage, and a schmitt trigger to provide switching hysteresis
for noise rejection, and open-collector output. An internal
bandgap regulator provides a temperature compensated
supply voltage for internal circuits and allows a wide operating
supply range.
When the magnetic flux density (B) is larger than operate
point (Bop), output is switched on (DO pin is pulled low). The
output state is held on until a magnetic flux density reversal
falls below Brp. When B is less than Brp, the output is
switched off.
The ATS177 is available in SIP-3L package.
Features
" Bipolar Hall-Effect latch sensor
" 3.5V to 20V DC operating voltage
" Temperature compensation
" Open-collector pre-driver
" 25mA maximum output sink current
" Built-in reverse polarity protection
" Operating temperature: -40癈 to +125癈
" SIP-3L package
" Green Molding Compound (No Br, Sb) (Note 1)
Pin Assignments
(Top View)
1. Vcc
2. GND
3.
DO
SIP-3L
Applications
" Brush-less DC Motor
" Brush-less DC Fan
" Revolution counting
" Speed measurement
Notes: 1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at
http://www.diodes.com/products/lead_free.html.
Typical Application Circuit
+12V
U1
ATS177
VCC
1
GND
2
OUTPUT
3
Q1
NPN
Q2
NPN
R1
2K
R2
3K
D1
+
C1
0.47uF
+
C2
0.47uF
L1
L2
Brush-less DC Fan
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ATS617LSGTN-T
IC HALL EFFECT GEAR SENSOR 4SIP
ATS625LSGTN-T
IC SENSOR GEAR TOOTH 4-SIP
ATS627LSGTN-T
IC HALL EFFECT GEAR SENSOR 4-SIP
ATS635LSETN-T
IC SENSOR GEAR TOOTH 4-SIP
ATS643LSHTN-I2-T
IC SENSOR GEAR TOOTH 4-SIP
ATS645LSHTN-I1
IC SENSOR GEAR TOOTH 4-SIP
ATS667LSGTN-T
IC SENSOR GEAR TOOTH 4SIP
ATS674LSETN-LT-T
IC SENSOR GEAR TOOTH 4-SIP
相关代理商/技术参数
ATS177PL
功能描述:工业霍耳效应/磁性传感器 SNGL BRUSHLESS LEAD-FREE RoHS:否 制造商:Honeywell 操作类型: 操作高斯: 工作电源电压: 电流额定值: 封装 / 箱体: 输出下降时间: 工作点最小值/最大值: 安装风格: 最大工作温度: 最小工作温度: 最大输出电流: 封装:
ATS177PLA
功能描述:板机接口霍耳效应/磁性传感器 Single Brushless RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23
ATS177-PL-A
制造商:Diodes Incorporated 功能描述:HALL EFFECT SENSOR 25MA LATCH 5V/9V/12V/15V/18V 3SIP - Bulk
ATS177-PL-A-A
功能描述:板机接口霍耳效应/磁性传感器 HALL IC SNSR LATCH 3.5V-20V 25MA RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23
ATS177-PL-A-B
功能描述:板机接口霍耳效应/磁性传感器 HALL IC SNSR LATCH 3.5V-20V 25MA RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23
ATS177-PL-B-A
功能描述:板机接口霍耳效应/磁性传感器 BIPOLAR LATCHING 3.5V-20V 25mA RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23
ATS177-PL-B-B
功能描述:板机接口霍耳效应/磁性传感器 BIPOLAR LATCHNG 25mA 3.5V-20V RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23
ATS177W
功能描述:工业霍耳效应/磁性传感器 SNGL BRUSHLESS RoHS:否 制造商:Honeywell 操作类型: 操作高斯: 工作电源电压: 电流额定值: 封装 / 箱体: 输出下降时间: 工作点最小值/最大值: 安装风格: 最大工作温度: 最小工作温度: 最大输出电流: 封装: